Stabilization of Cubic Zirconia with Manganese Oxide

A directionally solidified eutectic (DSE) of MnO-ZrO₂ has been investigated using a variety of electron optical techniques. It is found that considerable MnO goes into ZrO₂ to form a substitutional solid solution. About 14 wt% of MnO is soluble in ZrO₂ close to the eutectic temperature. The solubility of ZrO₂ in MnO, however, is quite low, less than 0.50 wt%. Electron diffraction experiments indicate that ZrO₂ (MnO) has the cubic fluorite structure. Diffuse scattering, similar to other cubic zirconias (e.g., CaO, MgO stabilized zirconia), is also observed in manganese-stabilized zirconia. Diffuse scattering indicates the presence of oxygen vacancies and thus confirms the defect nature of the fluorite structure. Electron energy loss spectrometry (EELS) fine structure analysis of the Mn L₂₃ edge provided clear evidence that Mn is present as Mn²⁺ in Mn-stabilized cubic ZrO₂.     

Distribution of Etoposide-Loaded Hydrophilic Albumin Microspheres in Mice

Hydrophilic albumin microspheres of etoposide were prepared by the emulsion polymerization technique using glutaraldehyde as the cross-linking agent. The microspheres prepared had a mean diameter of 1.5 μm. The microspheres were injected into mice by the intravenous route. In all, 12 mice were selected for the study, out of which 10 were given the drug-loaded microspheres and 2 were kept as solvent control. The mice were sacrificed after 24 hr and the accumulation of drug was determined in lungs, liver, and kidney.     

Structure and properties of some vegetable fibres

The stress-strain curves for pineapple leaf fibre have been analysed. Ultimate tensile strength (UTS), initial modulus (YM), average modulus (AM) and elongation of fibres have been calculated as functions of fibre diameter test length and test speed. UTS, YM, and elongation lie in the range of 362 to 748 MN m^–2, 25 to 36 GN m^–2, and 2.0 to 2.8%, respectively for fibres of diameters ranging from 45 to 205m. UTS Was found to decrease with increasing test lengths in the range 15 to 65 mm. Various mechanical parameters show marginal changes with change in speed of testing in the range of 1 to 50 mm min^–1. The above results are explained on the basis of structural variables of the fibre. Scanning electron microscope studies of the fibres reveal that the failure of the fibres is mainly due to large defect content of the fibre bo1h along the fibre and through the cross-section, The crack is always initiated by the defective cells and further aggravated by the weak bonding material between the cells.     

Uptake of Pb(II) and Cd(II) by a new phenolformaldehyde polymer resin derived by the insertion of sulfur ligands in the form of xanthate

A new phenolformaldehyde polymer resin containing potential soft‐type donor atoms (sulfur atoms) was synthesized by the reaction of sodium salt of 2,4‐dihydroxyacetophenone formaldehyde resin with carbon disulfide. The resin was characterized by elemental analysis, IR, and ¹H‐NMR spectral studies. Because of its insolubility in aqueous media, the resin was successfully used in the removal of Pb(II) and Cd(II). Parameters such as the effect of pH, the effect of time, competitive studies, the effect of initial metal‐ion concentration, and the recyclability of the polymer resin were studied. The amount of metal removed by the resin was determined with atomic absorption spectrophotometry. The retention properties were strongly dependent on pH. The elution of metal ions was investigated in acid media. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1932–1936, 2004     

Bubble temperature data for phenol-alcohol systems: Phenol-I-Amyl alcohol and phenol-n-Amyl alcohol systems

In order to supplement the literature data on VLE, isobaric bubble temperature data were collected for the binary systems phenol-i-amyl alcohol and phenol-n-amyl alcohol over the entire composition range by indirect method using a standard Swietoslawski type ebulliometer. The measurements were made at three sub-atmospheric pressures. The experimental t-x data were correlated with both equation of state method and gamma-phi methods. In the former approach, the Soave equation of state is used, whereas in the latter case Wilson, NRTL and UNIQUAC equations are used.     

State complexity of unique rational operations

For each basic language operation we define its “unique” counterpart as being the operation that results in a language whose words can be obtained uniquely through the given operation. These unique operations can arguably be viewed as combined basic operations, placing this work in the popular area of state complexity of combined operations on regular languages. We study the state complexity of unique rational operations and we provide upper bounds and empirical results meant to cast light into this matter. Equally important, we hope to have provided a generic methodology for estimating their state complexity.     

TCAM architecture for IP lookup using prefix properties

In modern IP routers, Internet protocol (IP) lookup forms a bottleneck in packet forwarding because the lookup speed cannot catch up with the increase in link bandwidth. Ternary content-addressable memories (TCAMs) have emerged as viable devices for designing high-throughput forwarding engines on routers. Called ternary because they store don't-care states in addition to 0s and 1s, TCAMs search the data (IP address) in a single clock cycle. Because of this property, TCAMs are particularly attractive for packet forwarding and classifications. Despite these advantages, large TCAM arrays have high power consumption and lack scalable design schemes, which limit their use. We propose a two-level pipelined architecture that reduces power consumption through memory compaction and the selective enablement of only a portion of the TCAM array. We also introduce the idea of prefix aggregation and prefix expansion to reduce the number of routing-table entries in TCAMs for IP lookup. We also discuss an efficient incremental update scheme for the routing of prefixes and provide empirical equations for estimating memory requirements and proportional power consumption for the proposed architecture.     

Effects of activator characteristics on the reaction product formation in slag binders activated using alkali silicate powder and NaOH

The influence of different levels of alkalinity, expressed using the Na₂O-to-source material ratio (n) and activator SiO₂-to-Na₂O ratio (M_s), on the compressive strength development of, and reaction product formation in sodium silicate and NaOH powder activated slag binder systems is discussed. Higher n value mixtures are found to exhibit higher early and later age compressive strengths. An increase in M_s results in reduced early age and slightly increased later age strengths. Compositional coefficients, which are functions of n and M_s are proposed, that relate to the early and later age strengths of the activated slag binders as well as to the shift in the FTIR spectra. The reaction product formation in these systems as a function of the total alkalinity is explained using the shifts of the dominant peak in the FTIR spectra. Fundamental changes in reaction products of powder activated binders as a function of alkalinity is observed. The deductions from the peak shifts are substantiated using the FTIR spectra of the pastes before and after salicylic acid–methanol (SAM) attack.